The control of paracetamol particle size and surface morphology through crystallisation in a spray dryer

The parameters governing the crystallisation of paracetamol using various conventional techniques has been extensively studied, however the factors influencing the drug crystallisation using spray drying is not as well understood. The aim of this work was to investigate the crystallisation of an active pharmaceutical ingredient through evaporative crystallisation using a spray dryer to study the physicochemical properties of the drug and to use semi-empirical equations to gain insight into the morphology and particle size of the dried powder. Paracetamol solutions were spray dried at various inlet temperatures ranging from 60 °C to 120 °C and also from a series of inlet feed solvent compositions ranging from 50/50% v/v ethanol/water to 100% ethanol and solid-state characterisation was done. The size and morphology of the dried materials were altered with a change in spray drying parameters, with an increase in inlet temperature leading to an increase in particle Sauter mean diameter (from 3.0 to 4.4 µm) and a decrease in the particle size with an increase in ethanol concentration in the feed (from 4.6 to 4.4 µm) as a result of changes in particle density and atomised droplet size. The morphology of the dried particles consisted of agglomerates of individual crystallites bound together into larger semi-spherical agglomerates with a higher tendency for particles having crystalline ridges to form at higher ethanol concentrations of the feed.     

纸基底印刷无芯片RFID湿度传感器* .txt

摘要：提出了一种基于纸基底的喷墨印刷无芯片RFID湿度传感器，通过遗传算法与射频仿真软件HFSS相结合，对常规开口环谐振器结构进行分布式加载，得到目标频率为245 GHz的谐振特性良好的传感器模型；采用DMP3000型材料打印机，在不同纸基底上喷墨印刷银墨水制作传感器，以纸张本身的吸水性实现湿度传感；研究不同纸基底对湿度传感器感湿灵敏度和恢复度的影响。结果表明，柯达相纸传感器的灵敏度最高，高湿灵敏度可达到8 MHz%RH，双铜纸湿度传感器恢复度高且恢复时间短，仅为2 min；两种基底湿度传感器皆有较好的一致性、中长期稳定性，且湿敏特性在20℃～30℃范围内受温度影响较小。对纸基湿度传感器的感湿机理进行了分析，纸主要成分纤维素表面的羟基与吸附的水分子作用形成氢键，改变了基底的介电参数，传感器的湿敏特性与纸的成分和结构有关。 .txt     

含La2O3奥氏体不锈钢堆焊合金层晶粒细化机制及对其耐腐蚀、磨损性能的影响

目的 通过在超低碳Cr19Ni10不锈钢堆焊合金中加入稀土氧化物La2O3，细化其微观组织，获得力学性能、耐腐蚀性能和耐磨性能等综合性能优良的堆焊合金层。方法 采用添加La2O3的超低碳Cr19Ni10不锈钢焊条制备了四种不锈钢堆焊合金。采用X射线荧光光谱、红外碳硫分析仪和X射线衍射分析仪，对堆焊合金层的元素组成和相组成进行了测定。采用金相显微镜和晶粒度统计软件，对堆焊合金层的微观组织形貌进行观察，并对晶粒度进行了统计分析。采用显微维氏硬度计和纳米压痕仪对堆焊合金层的硬度和杨氏模量进行了测定。采用电化学工作站和CSM摩擦磨损试验机对堆焊合金层的耐腐蚀性能和耐磨性能进行了评价，并且采用白光共聚焦显微镜对磨损后的磨痕形貌和尺寸进行了观察和测定。采用二维晶格错配度理论，对La2O3/γ-Fe界面间的晶格错配关系进行了计算。结果 在堆焊合金层中加入La2O3，随着La2O3加入量的增加，堆焊合金层奥氏体晶粒细化越明显。当La2O3的添加量由0%增加至1.5%时，奥氏体晶粒平均面积由400 μm²减少为210 μm²。堆焊合金层加入La2O3，可以明显提高其力学性能、耐腐蚀性能和耐磨损性能。当La2O3的添加量由0%增加至1.0%时，堆焊合金层的微观硬度由180HV增加到225HV，宏观硬度由125HBS增加到150HBS，杨氏模量由186 GPa左右增加到217 GPa，腐蚀电位由?0.4 V增加到?0.25 V，磨痕深度由50 μm减小到10 μm。La2O3(001)面和γ-Fe(110)面的二维晶格错配度为8.7%(<12%)，说明La2O3可以作为γ-Fe的中等有效异质形核基底，从而细化了堆焊合金层中的奥氏体晶粒。结论 La2O3可以有效地细化奥氏体晶粒，改善堆焊合金层的力学性能，提高其耐腐蚀和耐磨损性能。但是，La2O3加入量存在一个最佳值，当La2O3的加入量为1.0%时，堆焊合金层的综合性能最好。     

Controllable synthesis of glass ceramics containing YF3:Eu3+ nanocrystals: Well-preserved Eu and prolonged lifetime

Monolithic luminescent glass-ceramic (GC) embedded with fluoride-based nanocrystals (NCs) has drawn much attention as it is stable and possesses long fluorescent lifetime, while only small partial of optically active ions could enter the fluoride NCs prepared by conventional crystallization process. In this work, YF₃:Eu³⁺ embedded GCs have been controllably synthesized by Spark Plasma Sintering at a relatively low sintering temperature (960°C) within 10 minutes. The GC samples show typical sharp reddish-orange emissions peaking at λ = 590 nm and 620 nm, which can be ascribed to the ⁵D₀ → ⁷F_j transitions of Eu³⁺ located in the tetrahedral coordination sites of the YF₃ NCs. Significantly, a small R/O ratio (photoluminescence intensity ratio of ⁵D₀ → ⁷F₂/⁵D₀ → ⁷F₁) suggests that majority of Eu³⁺ ions are well preserved in YF₃ NCs, which is confirmed by the EDS and TEM results that highly crystallized YF₃:Eu³⁺ NCs are homogeneously dispersed into the silica glass matrix without interfacial reaction. Hence, the lifetime of GC sample is prolonged to 6.8 ms These results demonstrate that Eu³⁺ could be well protected and resided in YF₃ low phonon crystal by this method to fabricate GC composites with high optical performance.     

Facile synthesis of the desired red phosphor Li2Ca2Mg2Si2N6:Eu2+ for high CRI white LEDs and plant growth LED device

The red emission with suitable peak wavelength and narrow band is acutely required for high color rendering index (CRI) white LEDs without at the cost of the luminous efficacy. Herein, the Li₂Ca₂Mg₂Si₂N₆:Eu²⁺ red phosphor was prepared with facile solid-state method using Ca₃N₂, Mg₃N₂, Si₃N₄, Li₃N, and Eu₂O₃ as the safety raw materials under atmospheric pressure for the first time, which shows red emission peaking at 638 nm with full width at half maximum (FWHM) of 62 nm under blue light irradiation and becomes the desired red phosphor to realize the balance between luminous efficacy and high CRI in white LEDs. The morphology, structure, luminescence properties, thermal quenching behavior, and chromaticity stability of the Li₂Ca₂Mg₂Si₂N₆:Eu²⁺ phosphor are investigated in detail. Concentration quenching occurs when the Eu²⁺ content exceeds 1.0 mol%, whereas high-temperature photoluminescent measurements show a 32% drop from the room-temperature efficiency at 423 K. In view of the excellent luminescence performances of Li₂Ca₂Mg₂Si₂N₆:Eu²⁺ phosphor, a white LEDs with CRI of 91 as a proof-of-concept experiment was fabricated by coating the title phosphor with Y₃Al₅O₁₂:Ce³⁺ on a blue LED chip. In addition, the potential application of the title phosphor in plant growth LED device was also demonstrated. All the results indicate that Li₂Ca₂Mg₂Si₂N₆:Eu²⁺ is a promising red-emitting phosphor for blue LED-based high CRI white LEDs and plant growth lighting sources.     

Structural-microstructural characterization and optical properties of Eu3+,Tb3+-codoped LaPO4·nH2O and LaPO4 nanorods hydrothermally synthesized with microwaves

Rhabdophane-type Eu³⁺,Tb³⁺-codoped LaPO₄·nH₂O single-crystal nanorods with the compositions La_0.99999-xEu_xTb_0.00001PO₄·nH₂O (x?=?0–0.03), La_0.99999-yTb_yEu_0.00001PO₄·n′H₂O (y?=?0–0.010), and La_0.99999-zTb_zEu_0.000007PO₄·n′′H₂O (z?=?0–0.012) were hydrothermally synthesized with microwaves. It is shown that the Eu³⁺,Tb³⁺ codoping does not affect the thermal stability of these nanorods, which is due to the formation of substitutional solid solutions with both Eu³⁺ and Tb³⁺ replacing La³⁺ in the crystal lattice. Moreover, it is also shown that monazite-type Eu³⁺,Tb³⁺-codoped LaPO₄ single-crystal nanorods can be obtained by calcining their rhabdophane-type Eu³⁺,Tb³⁺-codoped LaPO₄·(n,n′ or n′′)H₂O counterparts at moderate temperature in air, and that they are thermally stable. It is also observed that, for the same Eu³⁺,Tb³⁺-codoping content, the monazite-type Eu³⁺,Tb³⁺-codoped LaPO₄ nanorods exhibit higher photoluminescent efficiency than the rhabdophane-type Eu³⁺,Tb³⁺-codoped LaPO₄· (n,n′ or n′′)H₂O nanorods. Moreover, it is found that the highest photoluminescence emission corresponds to the monazite-type La_0.96999Eu_0.02Tb_0.00001PO₄ nanorods for the La_0.99999-xEu_xTb_0.00001PO₄ system. However, for those compositions energy transfer from Tb³⁺ to Eu³⁺ does not occur. In addition, for an efficient energy transfer to occur, a content of at least 1?mol% Tb³⁺ is needed in all the studied materials.     

Influence of LiBO2 addition on the microstructure and lithium-ion conductivity of Li1+xAlxTi2−x(PO4)3(x = 0.3) ceramic electrolyte

Concerning the safety problems of conventional Li-ion batteries with liquid electrolytes, it is crucial to develop reliable solid-state electrolytes with high ionic conductivity. Li_1+xAl_xTi_2?x(PO₄)₃ (LATP, x = 0.3) is regarded as one of the most promising solid electrolytes due to its high ionic conductivity and excellent chemical stability to humidity.Herein, a new strategy is proposed for improving the sintering behavior and enhancing the ionic conductivity of LATP by using LiBO₂ as the sintering aid via liquid phase sintering. The as-prepared sample LATP with homogeneous microstructure and high relative density of 97.1% was successfully synthesized, yielding high total ionic conductivity of 3.5 × 10^?4 S cm^?1 and low activation energy of 0.39 eV at room temperature. It was found that the addition of LiBO₂ could effectively enhance the densification and increase the ionic conductivity of LATP electrolyte, proving an effective way to synthesis LATP ceramics by a simple and reliable route.     

面向球幕投影系统的几何校正方法

摘 要：用于飞行模拟的视景仿真系统，经常会以多台投影仪同步投影以得到较大范围的 视场角。当投影机斜对屏幕或者投影屏幕为曲面时，图像会发生几何失真。针对此问题，本文 提出了一种专门面向球幕投影系统的几何校正方法，并以一个三通道显示系统为实例，详述了 该方法的理论原理以及校正流程。实例结果表明，经几何校正后，各投影图像无几何畸变，通 道过渡处几何内容完全一致。该方法是一种纯软件方法，成本小而且操作简单，能够适应于不 同的投影场景。     

Risk factors associated to musculoskeletal disorder perception in college students,Bogota, 2016

Musculoskeletal disorders (MSD) have a high impact on the health of dual role workers (student and work). The aim of this study was to analyse risk factor (active pauses and job position) associated with MSD in postgraduate students, Bogotá 2016. This Cross-sectional study was conducted in a random sample of 304 college graduate students and statistical analysis in SPSS version 24. We found that significant differences between non-performing active pauses and neck symptoms (P = 0.007), not stretching vs neck symptoms [OR = 2.4048 (1.0133–5.707)]; laptop use vs eyes [OR = 2.7132 (1.457–5.0526)], shoulders [OR = 10.6364 (4.9905–22.6697)], elbows (P = 0.04); non-mouse usage vs elbows (P = 0.028), hand-wrist (P = 0.043); non-forearm support vs lower back (P = 0.009). Results suggest association between non-performing active pauses, stretching and neck; use of laptop and eyes, shoulders and left elbow, non-mouse usage and on elbow and hand/right wrist, no forearm support on table and lower back. Symptom changes in the upper and lower limbs were identified.